Search walchem.com
 
     

W600 Software Revision Level Descriptions

Upgrade Software


Always upgrade to the latest version for the greatest reliability! We are continuously improving the W600! Here are the features we have included lately. Please note that if you have an early revision of the software, you may only update to the latest revision, not to any intermediate revision.

Version 3.07
  • Fixed an issue where the pulse proportional control pulse rate could be twice the expected rate.
  • Fixed an issue where the conductivity reading displayed is not updated immediately following boiler intermittent sampling if trapped sampling is disabled.
  • Fixed an issue where resuming control is delayed for several seconds after a biocide bleed lockout or probe wash hold time of 0.
Version 3.05
  • Fixed an issue where an On Delay or Off Delay can stop before the programmed amount of time
Version 3.03
  • New Feed Monitor digital input type
  • The feature where a biocide or timer event can be selected to occur immediately after an interlock clears has been re-named from “Interlock Delay” to “Add Last Missed”
  • Conductivity-based biocide prebleeds will now be forced to have a time limit also associated, so it’s no longer possible for the prebleed to last forever
  • Added an Air Calibration for contacting conductivity sensors to improve accuracy
  • Modified the % Timer algorithm so that a new cycle starts if the sample period setting is changed
  • Fixed an issue in W600 where Web Server Failure alarms are not cleared from the display after the alarm is cleared
  • Fixed an issue in the W600 where too many timer events can result in a reboot
  • Increased the maximum setting allowed for the paddlewheel K factor
  • Fixed an issue in Timer control mode Hourly event repetition settings changing after a restart
  • Fixed an issue where a Flow Timer control output can stop accumulating feed time if interlocked by another output
  • Fixed an issue with PID control mode if the input is paddlewheel or virtual input type
Version 3.01
  • New combination Sensor Input and Analog Input board that add even more flexibility
  • Modbus/TCP communications
  • Graphing capability is now extended to web pages as well as the local display
  • Two Virtual Inputs that are calculated from two real inputs (cycles of concentration, % rejection, etc.)
  • PID control using Pulse or Analog outputs
  • On and Off Delays added to some control algorithms
  • Lead/Lag control of up to 6 relay outputs
  • Intermittent Sampling for boilers without using a trapped sample
  • Added a 2nd flowmeter input to the Feed Timer control algorithm
  • Antimony pH sensor support
  • Ability to restore default settings
  • Chinese and Taiwanese languages
  • Ability to choose to feed the last missed Biocide after an interlock
  • Ability to set the flow total to match the meter’s register
  • Total support for eService Reports
  • Modified Bleed/Feed and % Timer algorithms so a feed cycle doesn’t begin immediately after and interlock clears
  • Improved system stability
  • Improved sensor speed of response
Version 2.11
  • Fixes a problem in 2.09 where Flow Based Feed will not occur after an Interlock is cleared
  • Fixes a problem in 2.09 where Intermittent Sampling doesn’t operate the control valve correctly
  • Fixes a problem in 2.09 where the Minimum Relay Cycle time that is used with motorized ball valves is not used correctly
Version 2.09

This software upgrade improves performance and reliability of several existing features:

  • Decreased the time required to download log files
  • Improved the speed and reliability of VTouch Live Connect
  • Improved the speed and reliability of all Ethernet communications
  • Improved the reliability of the graph generation on the local display
  • Improved the reliability of configuration file imports
  • Corrected a problem loading the Display Settings menu that can occur when all possible inputs are being used
  • Corrected a problem where the analog output status can be incorrect
  • Improved webpage by eliminating expanding and collapsing links when hovering over them
  • More System Log messages to improve diagnosis
  • Improved handling of time changes in the graphs and data log files
  • Improved accuracy of timers
Version 2.07
Adds support for:
  • Sending emails (alarm or datalog) directly from the W600
  • LiveConnect to W600 via VTouch
  • Control based on paddlewheel flowrate
  • ORP Spike control mode
  • Duty cycle with on/off control mode
  • Easier biocide, industrial timer and probe wash programming
  • Ability to download data since the last time data was downloaded, plus more flexible log lengths and time between data points
  • Calibration reminder
  • Automatic reset of flow total (daily, monthly, annually)
  • Totalize time that a digital input (like a flow switch) has been open or closed
  • 4 parameters on the Home screen
  • Delay alarm notifications on system startup
  • Improved Ethernet connectivity
  • Fixed pulse proportional control output going below the minimum setting
  • Fixed issue with changing modes from webpages when using French language
  • Reduced low limit for temperature sensors to -20 C, -4 F
  • Disabled the Home screen timeout during log file transfers
Version 2.05
Adds support for:
  • Automatic buffer recognition for pH calibration
  • Three point buffer calibration for pH sensor
  • Probe wash relay control mode
  • Damping/averaging on sensor and analog inputs
  • User-adjustable conductivity automatic temperature compensation %
  • More flexible alarm relay control mode, able to select specific alarms that trigger the relay
  • Increase paddlewheel rate to 500 Hz.
  • Improvements to intermittent sampling calibration, and calibrations in general
  • Reset default calibration
  • Suppress sensor alarms during No Flow
  • Improvements to Ethernet connection stability
Version 2.03
Adds support for a Generic type sensor for use with any sensor that has a linear voltage output between -2 VDC and +2 VDC. Adds two new analog input types, one for a Fluorometer Input for use with the Little Dipper 2 sensor, and one for Transmitter for use if the device connected cannot be calibrated on its own and the W600 will need to be used to calibrate in engineering units of measure. The existing Generic AI type will be renamed AI Monitor. Adds adjustment to the brightness and contrast of the display. Adds the current day of the week to the Details screen for Biocide Timer and Timer control modes. Adds a menu to cancel the remaining feed time when using Bleed Then Feed control mode. Adds a new page of special characters, mostly Greek, available for text entry in all languages. During calibrations, the sensor reading will now be displayed and the user may force the calibration to completion if the value is not sufficiently stable for the controller to continue on its own.
Version 2.01
First released software version